LEEN Gearbox Conversion: LexusIS200 AZ6 to Toyota "A&qu
09-28-2011, 01:04 AM
Post: #1
LEEN Gearbox Conversion: LexusIS200 AZ6 to Toyota "A&qu
Many of you know about my trials and tribulations over getting the AZ6 adapter finished. Where I failed - Joe, from LEEN Gearbox Conversions, has spent the time, and money to bring this to the community. The first run of 5 units is now finished there is 4 units presold, that leaves one unit available for sale!!!! Once these 5 units are sold, Joe's intentions are to make a 2nd run, adding a few more units in each successive production runs.



LEEN Gearbox Conversions Wrote:And now, watch and enjoy Big Grin :thumbsup:

http://www.youtube.com/embed/siY-DbHbiO4


Over the last two weeks we have undertaken the fitting of a complete LEEN Adaptor kit, Gear Lever Kit, Speedometer Unit and Gearbox Bracket to an AE86. We now have our first LEEN 6 Speed AE86 Conversion complete and back in the hands of its owner ! No standard Car but a 182 BHP supercharged excellently modified machine !

I would particularly like to thank Joe (Joe81) for giving us the opportunity to test the components in his car. Also want to thank Shaft Tec based in Charleville for an excellent job on the driveshaft and also thanks to Brian who worked with me throughout the installation.

It begins .... :eek:

Here is the Car in question ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

Remove one T50 gearbox and add a pilot extension ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

Add a custom LEEN 6 Paddle clutch which engages the SXE10 Input Shaft (at LEEN we like the number 6 Wink)...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

Bolt on the pressure plate ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]


Then take one 6 Speed IS200 gearbox and add a LEEN SXE10 AE86 Adaptor Kit and a LEEN Gear Lever Kit ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

+

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

and you get a LEEN IS200 Gearbox ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

Install into a willing AE86 ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

And for good measure without the clutch and pressure plate installed verify the input shaft engages the pilot bearing extension ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

Check the clearance down the passengers side and no modification to the tunnel required !!!

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

And also on the right ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

Verify the location of the Gear Lever Unit, interesting - no modification to the tunnel required ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

From inside the car ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]

And finally ...

[Image: AEU86 AE86 - LEEN Gearbox Conversion: Le...t;A&qu]


Finally the most difficult part - giving it back Sad

Joe is testing the car as of Sunday morning and all is going well.

The speedometer is over reading, so I'm back checking ratio's and verifing the final drive. At this point if there is any aspects which need re-design I'm happy for them to be highlighted at this early stage. So not a problem !!

LEEN Gearbox Conversions is not VAT registered, so this basically means where ever you are in the world, these are the prices.

The minimum LEEN Gearbox Conversion Kit consists of the following:

SXE10 AE86 Adaptor (Aluminium 6082T6)
Sealant Plate (Aluminium 6082T6)
Pilot Bearing Extension (304 Stainless Steel)
Two Pilot Bearings
Clutch Disk (Standard or Paddle, 200mm or 212mm)

Price: €1291.36

Note: You will have to modify your own release bearing sleeve for the larger diameter input shaft of the IS200 gearbox or else buy the stainless steel replacement I manufacture. Once machined the wall thickness of the portion the release bearing slides on is reduced to 1.9mm. Because of the thin wall thickness I manufactured a stainless steel one; even with the thin 1.9mm wall it is still stronger than an original un-modified unit. Hence it will not fail in service.

LEEN Release Bearing Sleeve (304 Stainless Steel): €179.20 - HIGHLY recommended


Gear Lever Kit including modifing your gearbox to accept the parts: €248.00

Clutch Disk (Standard or Paddle, 200mm or 212mm): €156.80

Gearbox Bracket(transmission mount): €95.20

The speedometer unit is not available until I have it sorted. This company offers a solution: http://www.atrol.com/cablex.htm

I'm currently in talks with this company to supply their product, it's electronic based so it will suit any final drive ratio.

The plan is to adapt the kit to fit 6 speed gearboxes from the following:

Mazda Miata / MX-5

Mazda RX8

Nissan S15

So at present the IS200 is the only gearbox that definitely works with the adaptor. I will begin test fitting to the above gearboxes very soon.

The headache of VAT (Ireland's Value Added Tax) This may sound confusing ...

I had two options setting up the business, been VAT registered and not been VAT registered.

Basically if I am VAT registered the VAT I pay on the raw materials I can essentially claim back (making things cheaper for me to buy) but the TAX man must get his VAT somewhere so the customer is charged 21% VAT. That 21% VAT goes straight into the hand of the TAX man. This system involves making TAX returns every two months and associated accountant fees. So more operating costs and thus higher prices. If I was VAT registered people outside Europe would pay no VAT.

What I done is set up the business as a 'sole trader.' I'm not registered for VAT, and I can't claim back 21% of the value of the raw materials. I pay the full material price. So I pay the 21% VAT myself and this goes to the TAX man. Thus the price I charge is the price with the VAT allready paid by me, I can't take it off the price.

So the price is the same for anyone anywhere in the world. This is the simplist solution for me at present to manage this business.

Hope this explains things.

Thanks, Joe

LEEN Gearbox Conversions

http://www.gearboxconversion.com

Dan -

You can |Sad .... OR you can ask for help!!!

OST Porting service - http://hachiroku.net/forums/showthread.php?t=19991
Find all posts by this user


Messages In This Thread
LEEN Gearbox Conversion: LexusIS200 AZ6 to Toyota "A&qu - oldeskewltoy - 09-28-2011 01:04 AM
[] - Bean - 09-28-2011, 06:51 AM
[] - Eircamae86 - 09-28-2011, 12:53 PM
[] - Bean - 09-28-2011, 01:03 PM
[] - bozu - 09-29-2011, 02:31 AM
[] - oldeskewltoy - 09-29-2011, 02:43 AM
[] - DJexor - 09-29-2011, 02:59 PM
[] - oldeskewltoy - 09-29-2011, 08:25 PM
[] - DJexor - 09-30-2011, 09:58 AM
[] - bozu - 09-30-2011, 02:51 PM
[] - Bean - 09-30-2011, 04:17 PM
[] - ghost rider - 09-30-2011, 05:02 PM
[] - Bluedragon - 09-30-2011, 05:37 PM
[] - oldeskewltoy - 09-30-2011, 06:09 PM
[] - oldeskewltoy - 10-03-2011, 07:42 PM
[] - oldeskewltoy - 05-17-2013, 06:49 PM
[] - oldeskewltoy - 07-24-2013, 01:55 AM
[] - oldeskewltoy - 10-08-2013, 06:41 PM
[] - ditn - 10-08-2013, 07:54 PM
[] - makkuro - 10-09-2013, 07:01 PM
[] - Billy - 12-18-2013, 06:58 AM
[] - Project D - 12-18-2013, 06:00 PM
[] - oldeskewltoy - 12-18-2013, 11:27 PM
[] - oldeskewltoy - 02-12-2014, 06:42 PM

Possibly Related Threads...
Thread Author Replies Views Last Post
  Speed Industries: F20c conversion parts (mounts..) speed-inc 4 5,252 02-09-2012 11:11 PM
Last Post: roiz86
  Speed Industries: f20c conversion parts speed-inc 2 3,010 06-22-2009 02:35 PM
Last Post: benjy_b
  AZ6 Swap Available! oldeskewltoy 8 12,222 10-23-2007 06:57 AM
Last Post: oldeskewltoy
  "old school > everything else" sticker OSI 1 3,478 01-11-2006 08:31 AM
Last Post: OSI
  "I Love My POS" Stickers OSI 9 7,486 11-30-2005 08:27 PM
Last Post: OSI

Forum Jump:


User(s) browsing this thread: 2 Guest(s)

Contact Us | AEU86 | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication