What camshafts would be nice?

Threaded Mode | Linear Mode

What camshafts would be nice?

08-25-2010, 12:00 AM

Post: #42

apardal Offline

Senior Member

Posts: 512
Joined: Jan 2005
Reputation: 0

Dan, I don't think it is appropriate to argue about dyno's and their accuracy on this topic, but dyno numbers are hardly a rule of thumb to compare engine power outputs.

My facts are:

298º Kent camshafts (264º at 1mm of lift) and 9.4mm of maximum lift.

143whp (170hp) @ 8100 rpm.

[Image: AEU86 AE86 - ]

So it is likely that given my setup and assuming it is properly tuned, it'll be producing more power than yours, but numbers are almost exactly the same and I suppose on the road it wont be the same.

Just to say that it is hard to present facts beyond reasonable doubt with dyno sheets, to help Patrick decide on which cams to go for.

« Next Oldest | Next Newest »

Messages In This Thread

What camshafts would be nice? - PatrickAE86 - 08-16-2010, 06:44 PM

[] - robokill - 08-16-2010, 06:53 PM

[] - PatrickAE86 - 08-16-2010, 07:03 PM

[] - totta Crolla - 08-16-2010, 08:06 PM

[] - PatrickAE86 - 08-16-2010, 10:35 PM

[] - apardal - 08-16-2010, 10:49 PM

[] - BOOMEX - 08-19-2010, 03:49 AM

[] - PatrickAE86 - 08-19-2010, 10:46 AM

[] - waffenschmiede - 08-19-2010, 11:14 AM

[] - Uzelac - 08-19-2010, 12:00 PM

[] - BOOMEX - 08-19-2010, 12:39 PM

[] - Project D - 08-19-2010, 12:47 PM

[] - BOOMEX - 08-19-2010, 12:54 PM

[] - Project D - 08-19-2010, 01:12 PM

[] - PatrickAE86 - 08-19-2010, 01:21 PM

[] - Project D - 08-19-2010, 02:01 PM

[] - robokill - 08-19-2010, 06:10 PM

[] - waffenschmiede - 08-19-2010, 07:59 PM

[] - Project D - 08-19-2010, 08:02 PM

[] - Bean - 08-19-2010, 08:34 PM

[] - Jan Pedersen - 08-19-2010, 09:08 PM

[] - apardal - 08-19-2010, 10:29 PM

[] - Project D - 08-19-2010, 11:17 PM

[] - robokill - 08-20-2010, 01:34 AM

[] - PatrickAE86 - 08-20-2010, 06:24 PM

[] - Bean - 08-21-2010, 04:13 PM

[] - Project D - 08-21-2010, 05:01 PM

[] - PatrickAE86 - 08-21-2010, 07:28 PM

[] - totta Crolla - 08-21-2010, 07:58 PM

[] - Bean - 08-22-2010, 12:41 PM

[] - PatrickAE86 - 08-22-2010, 02:31 PM

[] - harkes - 08-22-2010, 03:53 PM

[] - Bean - 08-22-2010, 04:01 PM

[] - Bean - 08-22-2010, 04:03 PM

[] - isac - 08-22-2010, 08:40 PM

[] - Project D - 08-22-2010, 09:13 PM

[] - Bean - 08-22-2010, 10:06 PM

[] - isac - 08-23-2010, 09:21 PM

[] - Bean - 08-23-2010, 10:15 PM

Re: What camshafts would be nice? - oldeskewltoy - 08-24-2010, 12:40 AM

Re: What camshafts would be nice? - Bean - 08-24-2010, 03:19 PM

[] - apardal - 08-25-2010 12:00 AM

Re: What camshafts would be nice? - oldeskewltoy - 08-25-2010, 12:08 AM

[] - ZDoman - 08-25-2010, 12:46 PM

[] - Uzelac - 08-25-2010, 01:06 PM

Possibly Related Threads...
Thread		Author	Replies	Views	Last Post
	How would/have you rebuild your 4age?	joaotcgt	6	9,903	07-21-2015 10:40 AM Last Post: mad.matt
	4AGE camshafts (again)	Alex170984	26	32,395	03-19-2013 02:41 PM Last Post: Alex170984
	what clutch would you recommend	megabob	12	12,433	02-22-2010 03:36 PM Last Post: NoHachi
	4age bogs. Would like some help!	root	4	6,372	12-30-2009 11:10 AM Last Post: Nomuken
	9.5mm lift camshafts with OEM followers... anyone?	apardal	9	9,942	10-15-2008 03:24 PM Last Post: robokill

User(s) browsing this thread: 1 Guest(s)