1 Dead front strut.
05-28-2005, 06:54 PM
Post: #1
1 Dead front strut.
Well, I finally figured out where my shaky steering was coming from

The nearside techno pro spirit insert seems to be buggered - I can grab the piston and just shake it around. I am guessing they cannot be rebuilt very easily. Sad

Anyone have any ideas ? probably gonna have to replace them.

Regards Ian.
[Image: AEU86 AE86 - 1 Dead front strut.]
Visit this user's website Find all posts by this user
05-28-2005, 07:13 PM
Post: #2
1 Dead front strut.
I´m just gonna answer this the best i can, if i misunderstood the question, just forget what i´m about to say.

Normally....Inserts into the front damber casings, are supposed to be loose. You do, though, need to fill up the chamber betweeen the insert and the housing with oil. This is done to optimize cooling, and don´t let anybody tell you different.
So if what you´re saying is that you have taken your strut apart and found the insert loose inside, this is normal, and not to be altered, except with the oil i mentioned.

My evil Red/Black Panda
http://www.bilgalleri.dk/html/gal_visbil.asp?ID=12832
My current JDM AE86 project
http://www.bilgalleri.dk/html/gal_visbil.asp?ID=31609
Find all posts by this user
05-28-2005, 07:55 PM
Post: #3
1 Dead front strut.
Not taken it apart - if I hold the strut and grab the piston from the insert it wobbles around like hell - the other side does not. I thought it may be the lower ball joint that was gone but that seems ok.

On another note - just dropped a set of Mintex 1144 pads in the 4potters. Stopping power is very good and consistent.

Regards Ian.
[Image: AEU86 AE86 - 1 Dead front strut.]
Visit this user's website Find all posts by this user
05-30-2005, 01:30 PM
Post: #4
1 Dead front strut.
Ok,

does anyone happen to know the length of an ae92 TRD insert ? - thats what I think I have right now.

I am hearing that TOKICO HTS is probably the best way to go - I just need to figure out the insert length. Hopefully the strut casings have been cut down to the right length and its just a case of packing out the casing to take the new one.

Anyone know how the TOKICO inserts compare to the Techno Toy Tuning AGX inserts compare ?

Regards Ian.
[Image: AEU86 AE86 - 1 Dead front strut.]
Visit this user's website Find all posts by this user
05-30-2005, 03:53 PM
Post: #5
1 Dead front strut.
Ian.G Wrote:Ok,

does anyone happen to know the length of an ae92 TRD insert ? - thats what I think I have right now.

I installed stock KYB AE92 inserts - they are 40 mm shorter than stock AE86 ones. If you know difference between stock and TRD ones - voila !
Visit this user's website Find all posts by this user
05-31-2005, 12:35 PM
Post: #6
1 Dead front strut.
TRD Japan now have a full english version of their parts list that can be searched Big Grin

http://trdparts.jp/english/

Anyone know if TRD still produce the ae92 inserts (either adjustable or not) ?

Regards Ian.
[Image: AEU86 AE86 - 1 Dead front strut.]
Visit this user's website Find all posts by this user
05-31-2005, 09:39 PM
Post: #7
1 Dead front strut.
Ian take a yellow koni very easy to get :-)

Cars:
"99 Lexus IS200
"86 AE86 Kouki Panda Levin GT-Apex (restore project)
"84 AE86 Zenki Blue Levin (project racer)
Motorcycles:
"02 Yamaha R1
"02 Honda Hornet S
"08 BMW R1200GS
Find all posts by this user


Possibly Related Threads...
Thread Author Replies Views Last Post
  TUV - Strut brace pack 3 4,706 09-08-2018 08:17 PM
Last Post: d3nso
  Need urgent help strut mounts. ditn 5 7,038 01-21-2012 03:37 PM
Last Post: ditn
  front strut lenght comparison problems fax0815 6 6,980 01-25-2011 04:12 PM
Last Post: fax0815
  Rear Strut heshan 5 5,763 01-02-2011 02:56 PM
Last Post: Sam-Q
  techno toy tuning rear strut tower braces....installation ?. J_who_ez 14 16,895 09-18-2010 04:33 PM
Last Post: PatrickAE86

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us | AEU86 | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication