Ivan's coupe (nice rack!)
11-15-2021, 09:59 AM
Post: #581
Ivan's coupe (nice rack!)
Nice one Ivan, steady does it. Smile
Find all posts by this user
11-27-2021, 10:50 PM
Post: #582
Ivan's coupe (nice rack!)
Today's progress (for lack of a better word):
Sprayed the wheel tubs with 3M rubberized stone chip coating.
The raptor liner beneath it is strong enough to withstand street use but I wanted some additional noise insulation.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Remembered to bring the fuel tank gaskets this time, so I finished off the tank.
My new fuel pump bracket came painted matte black, but I have very little faith in the longevity of toyota's paint, so I slapped some 2k black over it.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Same goes for the sender unit (this got a dose of rust converter first):
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Pouring out a little bit of paint is quite difficult, so after the brackets were painted I still had 3/4 of my mixed paint left in the gun. Sprinted to my big box of zink plated brackets and grabbed some stuff to empty the gun on.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
The little spots are a combination of solvent pop and dust.. serves me right for painting on the floor and in a hurry. But they are well protected from rust without the paint so I'm not too fussed.

Here is the assembled unit. I glued the old protection pads on with some special body trim glue. Got the orientation of one wrong but who cares eh?
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Mounting the thing will have to wait till I get myself a bit of new fuel hose

FABRICA MI DIEM, PVNC!
Visit this user's website Find all posts by this user
11-28-2021, 08:52 PM
Post: #583
Ivan's coupe (nice rack!)
Progress!

AE86 Levin
Find all posts by this user
12-18-2021, 12:20 AM (This post was last modified: 12-18-2021 12:25 AM by Ivan141.)
Post: #584
Ivan's coupe (nice rack!)
Had a bit of a marathon today.
Started out with scuffing up the engine bay, and painting it over with the gunmetal metallic and some 2k clear. This is the one place where the gunmetal remains visible so I wanted it shiny. Did not do a perfect job, but good enough for a noob painting at 8 deg C using a mini spraygun with a 0.8 nozzle (where 1.2 is recommended).
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Finally had my Gates Barricade fuel line in (both in-tank and regular), so I replaced the fuel pump to bracket hose and every other rubber fuel line on the car.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
Cleaned up the tank vent contraption:
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
Fuel line hookups.. that one bracket is a fail, should take it off to clean it up.
I'm sure either the pump or the sender will give me grief someday, so I'll get to it then.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

The money shot (quite literal knowing what I spent on this):
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

The filler neck is not perfectly centered but it will do. This is due to a combination of replica tank, and my new chassis rail interfering with the tank fitment a tiny bit.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
Will make something with my 3d printer sometime to make it look like it was intended that way.

FABRICA MI DIEM, PVNC!
Visit this user's website Find all posts by this user
12-21-2021, 04:45 PM
Post: #585
Ivan's coupe (nice rack!)
Nice! What’s next?

AE86 Levin
Find all posts by this user
12-21-2021, 05:54 PM (This post was last modified: 12-21-2021 05:55 PM by Ivan141.)
Post: #586
Ivan's coupe (nice rack!)
While I can still spin it around:
-Fab up some exhaust and gearbox heatshields
-Fit the front crossmember, and (ugly old) front stuts & rear axle so I can put it back on it's wheels.
-Refitting or fabbing the splash guard that shields the tank filler neck area from water and rubbish ingress.
-Shoot some more cavity wax into hard to reach corners and turn the car so it can seep into the seams.

Also have smaller jobs left and right that need doing:
-Refurbish the driveshaft (sadly affordable new bearings are out of stock everywhere, will have to reuse the old one since Toyota charges $390).
-Assemble my refurbished rear axle.

Once the car is on 4 wheels again it's bodywork time.

FABRICA MI DIEM, PVNC!
Visit this user's website Find all posts by this user
12-22-2021, 08:57 PM
Post: #587
Ivan's coupe (nice rack!)
Why not have a single piece drive shaft made? I’ve got one as well and in my opinion it works very well.

AE86 Levin
Find all posts by this user
12-25-2021, 11:17 AM
Post: #588
Ivan's coupe (nice rack!)
Looking good Ivan

Sent from my ANE-LX1 using Tapatalk
Find all posts by this user
01-01-2022, 09:16 PM
Post: #589
Ivan's coupe (nice rack!)
What better way to celebrate the new year than to tinker on the ol' dungheap again.

Last time I had a stab at building a heat shield from some embossed aluminiuim. Quite challenging to get as sturdy as I want it, so I will have to redo this with some thicker aluminium strips for structural support.
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Not pictured but did happen: Sprayed a whole lot more cavity wax around the roof, trunk and rear arches area.

Next I wanted to have some more tangible progress so I proceeded to slap on some shiny parts:
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]

Looking good IMO.

I was a bit upset about the amount of play between the new LCA bushings and the LCA bolts. There is almost a mm of play between the 2 of those. I get the feeling it's like this from factory but it feels kind of sloppy.

FABRICA MI DIEM, PVNC!
Visit this user's website Find all posts by this user
01-01-2022, 09:22 PM
Post: #590
Ivan's coupe (nice rack!)
That's a good New Year's resolution! And the work looks good! Thumbs up!

1982 - TA60 Carina 4dr sedan - fun cruiser
1983 - AE86 Sprinter Trueno - import project
2013 - Honda Civic sport - daily driver
2004 - AEU86 dot ORG - daily domain

Support our forum, buy from the AEU86 shop:
[Image: AEU86 AE86 - Ivan's coupe (nice rack!)]
Visit this user's website Find all posts by this user


Possibly Related Threads...
Thread Author Replies Views Last Post
  danish renovation, from rusty old banger, to nice drift car katapouser 16 12,511 12-23-2008 10:41 PM
Last Post: katapouser

Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us | AEU86 | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication